Read Ebook: The Seaman's Friend Containing a treatise on practical seamanship with plates a dictionary of sea terms customs and usages of the merchant service by Dana Richard Henry

Font size: 10 px 15 px 20 px 25 px 30 px 35 px

Background color: BlackWhiteGrayLight GrayDark GrayDim Gray

Text color: BlackWhiteGrayLight GrayDark GrayDim Gray

Apply/Save settings

Ebook has 1442 lines and 87849 words, and 29 pages

BALLAST AND LADING.--A ship's behavior, as the phrase is, depends as much upon the manner in which she is loaded and ballasted, as upon her model. It is said that a vessel may be prevented from rolling heavily, if, when the ballast is iron, it is stowed up to the floor-heads; because this will bring the ship back, after she has inclined, with less violence, and will act upon a point but little distant from the centre of gravity, and not interfere with her stiff carrying of sail. The cargo should be stowed with the weightier materials as near as possible to the centre of gravity, and high or low, according to the build of the vessel. If the vessel is full and low built, the heavy articles should be stowed high up, that the centre of gravity may be raised and the vessel kept from rolling too much, and from being too laborsome. But a narrow, high-built vessel should have the heavy articles stowed low and near the keelson, which will tend to keep her from being crank, and enable her to carry sail to more advantage.

CUTTING AND FITTING STANDING RIGGING.

Measuring and cutting lower rigging and lower fore-and-aft stays. Fitting the same. Measuring, cutting, and fitting topmast rigging, stays, and backstays. Jib, topgallant, and royal stays. Rattling down rigging. Cutting and fitting lifts, foot-ropes, brace-block straps, and pennants. Breast-backstays.

CUTTING LOWER RIGGING.--Draw a line from the side of the partners abreast of the mast, on the deck, parallel to the channels, and to extend as far aft as they do. On this line mark the places of each dead-eye, corresponding to their places against the channels. Send a line up to the mast-head, and fasten it to the mast by a nail above the bibbs, in a range with the centre of the mast, and opposite to the side the channel line is drawn upon. Then take the bight of the line around the forward part of the mast, and fasten it to the mast by a nail, opposite the first nail, so that the part between the nails will be half the circumference of the mast-head; then take the line down to the mark on the channel line for the forward dead-eye, and mark it as before; and so on, until you have got the distance between the mast and each mark on the channel line. Now cast off the line from the mast-head, and the distance between the end of the line and each mark will give you the length of each shroud from the lower part of the mast-head. And, to make an allowance for one pair of shrouds overlaying another, you may increase the length of the pair put on second, that is, the larboard forward ones, by twice the diameter of the rigging; the third pair by four times; and so on.

The size of the lower rigging should be as much as eight and a half inches for vessels of seven or eight hundred tons, and from seven and a half to eight for smaller vessels, over three hundred tons.

For the length of the fore, main, and mizzen stays and spring-stays, take the distance from the after part of the mast-head to their hearts, or to the place where they are set up, adding once the length of the mast-head for the collar.

The standing stays should be once and half the circumference of the shrouds.

The bolsters under the eyes of the rigging should always be covered with tarred parcelling, marled on.

The starboard forward shroud goes on first; then the larboard; and so on. The fore stay and spring stay go over the shrouds; and the head stays always go over the backstays.

CUTTING AND FITTING TOPMAST RIGGING.--For the forward shroud, measure from the hounds of the topmast down to the after part of the lower trestle-trees, and add to that length half the circumference of the mast-head at the hounds. The eye is once and a quarter the circumference of the mast-head. The topmast rigging in size should be three fifths of the lower rigging. For the topmast backstays, measure the distance from the hounds of the mast down to the centre of the deck, abreast of their dead-eyes in the channels, and add to this length one half the circumference of the mast-head. Add to the length of the larboard pair, which goes on last, twice the diameter of the rope. The size of the fore and main topmast backstays is generally one quarter less than that of the lower rigging; and that of the mizzen topmast backstays the same as that of the main topmast rigging. The size of the topmast stays should be once and a quarter that of the rigging. The topmast rigging is fitted in the same manner as the lower. The backstays should be leathered in the wake of the tops and lower yards. The breast-backstays are turned in upon blocks instead of dead-eyes, and set up with a luff purchase. The fore topmast stay sets up on the starboard, and the spring stay on the larboard side of the bowsprit.

All the fore-and-aft stays are now set up on their ends, and should be leathered in their nips, as well as in their eyes.

The main topmast stay goes through a heart or thimble at the foremast-head, or through a hole in the cap, and sets up on deck or in the top; and the mizzen topmast stay sets up at the mainmast-head, above the rigging.

JIB, TOPGALLANT, AND ROYAL RIGGING.--The jib stay sets up on its end on the larboard side of the head, and is served ten feet from the boom, and its collar is leathered like that of the topmast stay. The gaub lines or back ropes go from the martingale in-board. The guys are fitted in pairs, rove through straps or snatches on the spritsail yard, and set up to eye-bolts inside of or abaft the cat-heads. The foot-ropes are three quarters the length of the whole boom, and go over the boom-end with a cut splice. Overhand knots or Turks-heads should be taken in them at equal distances, to prevent the men from slipping, when laying out upon them.

The most usual method of fitting topgallant rigging in merchantmen, is to reeve it through holes in the horns of the cross-trees, then pass it between the topmast shrouds over the futtock staff, and set it up at an iron band round the topmast, just below the sheave-hole; or else down into the top, and set it up there. To get the length of the starboard forward shroud, measure from the topgallant mast-head to the heel of the topmast, and add one half the circumference of the topgallant mast-head. Its size should be about five sevenths of the topmast rigging. Each pair of shrouds should be served below the futtock staves. They are fitted like the topmast shrouds. The fore-and-aft stays of long topgallant masts go with eyes, and are served and leathered in the wake of the foot of the sails. The fore topgallant stay leads in on the starboard side of the bowsprit, and sets up to a bolt at the hawse-piece; the main leads through a chock on the after part of the fore topmast cross-trees, and sets up in the top; and the mizzen usually through a thimble on the main cap, and sets up on its end.

The topgallant backstays set up on their end, or with lanyards in the channels; and for their length, measure from the mast-head to the centre of the deck, abreast the bolt in the channels.

The royal shrouds, backstays, and fore-and-aft stays, are fitted like those of the topgallant masts, and bear the same proportion to them that the topgallant bear to the topmast. The fore royal stay reeves through the outer sheave-hole of the flying jib-boom, and comes in on the larboard side; the main through a thimble at the fore jack-cross-trees; and the mizzen through a thimble at the maintopmast cap. The flying jib-stay goes in on the starboard side, and sets up like the jib-stay. The gear of the flying jib-boom is fitted like that of the jib-boom.

STANDING RIGGING OF THE YARDS.--The first thing to go upon the lower yard-arm, next the shoulder, is the head-earing strap; the next, the foot-ropes; next, the brace-block; and lastly, the lift. The foot-ropes go with an eye over the yard-arm, are rove through thimbles in the end of the stirrups, and are lashed to bolts or thimbles, but now usually to the iron trusses. The stirrups fit to staples in the yard, with an eye-splice. The lifts should be single, and fitted with an eye over the yard-arm, and lead through a single block at the mast-head, and set up by a gun or luff tackle purchase, with the double block hooked to a thimble or turned in at the end, and the lower block to an eye-bolt in the deck. Instead of brace-blocks on the fore and main yards, brace-pennants fitted over the yard-arm with an eye are neater. The latest and neatest style of rigging lower yards is to have a strong iron band with eyes and thimbles round each yard-arm, close to the shoulder; and then fit the lift, foot-rope, and brace-pennant, each to one of these eyes, with an eye-splice round the thimble or with a hook. The lower lifts now, for the most part, cross each other over a saddle upon the cap, instead of going through blocks.

The inner ends of the foot-ropes to the topsail, topgallant and royal yards, cross each other at the slings; and on the topsail yard there are Flemish-horses, spliced round thimbles on the boom-iron, and the other end seized to the yard, crossing the foot-rope. A neater mode is to hook the outer end of the Flemish-horse, so that it may be unhooked and furled in with the sails when in port. Next to the foot-ropes go on the brace-blocks, and lastly, the lifts. The rigging to the topgallant and royal yards is fitted similarly to that upon the topsail, except that there is nothing over the yard-arms but foot-rope, brace and lift. The brace to the royal yard fits with an eye. The reef-tackle, studding-sail halyard, and other temporary blocks, are seized to the lower and topsail yard-arms by open straps, so that they may be removed without taking off the lift. The topgallant studding-sail halyard block is often hooked to the boom-iron, under the yard.

The foot-ropes to the spanker-boom should be half the length of the boom, going over the end with a splice, covered with canvass, and coming in one third of the way to the jaws, and seized to the boom by a rose-seizing through an eye-splice. The next to go over the boom-end are the guys, which are fitted with a cut-splice covered with canvass, and have a single block turned in at their other ends. To these single blocks are luff or gun-tackle purchases, going to the main brace-bumpkin. Their length should be two fifths that of the boom. The topping-lifts are usually hooked into a band or spliced into bolts about one quarter the distance from the outer end of the boom, and reeve through single blocks under the top, with a double or single block at their lower ends.

All the splices and seizings of the standing rigging should be covered with canvass, if possible, except in the channels and about the head, where they are too much exposed to the washing of water. A vessel looks much neater for having the ends of the rigging, where eyes are spliced, or where they are set up on their ends aloft or on deck, covered with canvass, and painted white or black, according to the place where they are. The lanyards and dead-eyes of the smaller rigging which sets up in the top may also be covered with canvass. The lanyards, dead-eyes, and turnings-in of the rigging in the channels, should always be protected by scotchmen when at sea, and the forward shroud should be matted or battened all the way up to the futtock staves.

In some smaller merchantmen the lower rigging is not infrequently set up upon its end to bolts in the rail. This is very inconvenient on many accounts, especially as all the seizings have to be come up with, and the nip of the shroud altered, whenever it is at all necessary to set them taut. This soon defaces and wears out the ends; while, with dead-eyes, only the lanyards have to be come up with. Some vessels set up their lower rigging with dead-eyes upon the rail. This is convenient in setting them up in bad weather, but does not give so much spread as when set up in the channels, and presents a more complicated surface to the eye. If the rigging is fitted in this way, you must deduct the height of the rail above the deck from the measure before given for cutting it.

BREAST-BACKSTAYS.--It is not usual, now, for merchant vessels to carry topmast breast-backstays. If they are carried, they are spread by out-riggers from the top. Topgallant and royal breast-backstays are used, and are of great assistance in sailing on the wind. There are various ways of rigging them out, of which the following is suggested as a neat and convenient one. Have a spar fitted for an out-rigger, about the size of one of the horns of the cross-trees, with three holes bored in it, two near to one end, and the third a little the other side of the middle. Place it upon the after horn of the cross-tree, with the last-mentioned hole over the hole in the end of the horn of the cross-tree, and let the after topgallant shroud reeve through it. Reeve the topgallant and royal breast-backstays through the outer holes, and set them up by a gun-tackle purchase, in the channels. The inner end of the out-rigger should fit to a cleat, and be lashed to the cross-tree by a lanyard. When the breast-backstays are to be rigged in, cast off the lanyard, and let the out-rigger slue round the topgallant shroud for a pivot, the inner end going aft, and the outer end, with the backstays, resting against the forward shroud. One of these out-riggers should be fitted on each side, and all trouble of shifting over, and rigging out by purchase, will be avoided.

The royal breast-backstay may be used as the fall of the purchase.

FITTING AND REEVING RUNNING RIGGING.

Fore braces. Main braces. Cross-jack braces. Fore, main, and mizzen topsail braces. Fore, main, and mizzen topgallant and royal braces. Trusses. Topsail tyes and halyards. Topgallant and royal halyards. Peak and throat halyards. Spanker brails. Fore and main tacks and sheets. Topsail, topgallant and royal sheets and clewlines. Reef-tackles. Clew-garnets. Fore and main buntlines, leechlines, and slablines. Topsail clewlines and buntlines. Bowlines.

TO RIG MASTS AND YARDS.

Rigging the shears. Taking in lower masts and bowsprit. To rig a bowsprit. Getting the tops over the mast-heads. To send up a top-mast. To get on a top-mast cap. To rig a jib-boom. To cross a lower yard. To cross a topgallant yard. To send up a topgallant mast. Long, short, and stump topgallant masts. To rig out a flying jib-boom. To cross topgallant and royal yards. Skysail yards.

TAKING IN LOWER MASTS AND BOWSPRIT.--Shore up the beams upon which the heels of the shears will rest, if necessary, from the keelson. Parbuckle the shears aboard, with their heads aft. Raise their heads upon the taffrail, cross them, and pass the shear-lashing. Lash the upper block of a three-fold tackle under the cross, and secure the lower block to the breast-hooks, or to a toggle in the hawse-hole. You may also reeve and secure, in the same manner, a smaller purchase, which shall work clear of the first. Have two forward and two after guys clove-hitched to the shear-head, with cleats to prevent their slipping. Get a girt-line on one shear-head and a small tackle on the other, to slue and cant the mast. Let the fall of the main tackle come through the middle sheave, to prevent the block's sluing in its strap. Reeve large heel tackles to rouse the shears aft with. Put long oak plank shoes under the heels; and, if it be necessary, clap a thwart-ship tackle upon the two heels, or reeve a lashing, and put a stout plank between them, and bowse taut; which will prevent too great a strain coming upon the water-ways. Take the main tackle fall to the capstan; heave round, haul on the forward guy and after heel tackles, and raise the shear to an angle of about eighty degrees with the deck, and so that the main purchase will hang plumb with the partners of the mizzen-mast. Lash a garland to the forward part of the mast, above the centre, and toggle the purchase to it. Heave the mast in over the bulwarks; fit the trestle-trees and after chock; reeve girt-lines by which men may be hoisted when the mast is in; point the mast in, and lower away. Always take in the mizzen-mast first. Get in the main and then the foremast in the same manner, rousing the shears forward, with their shoes, by means of the heel tackles. Having stepped and secured the foremast, carry the forward guys aft and rake the shears over the bows; toggle the lower block of the main tackle to a garland lashed to the upper part of the bowsprit inside of the centre. Put on the cap, and carry tackles or guys from the bowsprit-head to each cat-head, and clap on a heel tackle or guy. Heave the bowsprit, and direct it by the small tackles and guys.

TO RIG A BOWSPRIT.--Lash collars for the fore stay, bobstays, and bowsprit shrouds, then for the spring stay, and put on the bees for the topmast stays; fit the man-ropes, pass the gammoning, and set up bobstays and shrouds.

TO GET THE TOPS OVER THE MAST-HEADS.--Place the top on deck abaft the mast; get a girt-line on each side of the mast-head, and pass the end of each under the top, through the holes in the after part; clinch them to their own parts, and stop them to the fore part of the top with slip-stops. Have a guy to the fore and another to the after part of the top. Make the ends of a span fast to the after corners of the top, and bend a girt-line from the mast-head to the bight of the span, and stop it to the forward part of the top. Sway away on the girt-lines. When the fore part of the top is above the trestle-trees, cut the span-stops, and when the after part is above them, cast off the slip-stops. When the lubber-hole is high enough to clear the mast-head, haul on the forward guy, and let the top hang horizontally by the girt-lines. Lower away, place and bolt it.

The fore and main tops are sent up from abaft, and the mizzen from forward. The tops may be got over without the span and girt-line, by stopping the two girt-lines first rove to the middle as well as to the fore part of the top, and cutting the upper stops first.

TO SEND UP A TOPMAST.--Get the topmast alongside, with its head forward. Lash a top-block to the head of the lower-mast; reeve a mast-rope through it, from aft forward, and bring the end down and reeve it through the sheave-hole of the topmast, hitching it to its own part a little below the topmast-head, and stopping both parts to the mast, at intervals. Snatch the rope and sway away. As soon as the head is through the lower cap, cast off the end of the mast-rope, letting the mast hang by the stops, and hitch it to the staple in the other end of the cap. Cast off the stops and sway away. Point the head of the mast between the trestle-trees and through the hole in the lower cap, the round hole of which must be put over the square hole of the trestle-trees. Lash the cap to the mast, hoist away, and when high enough, lower a little and secure the cap to the lower mast-head. If the cross-trees are heavy, they may be placed in the following manner. Sway away until the topmast-head is a few feet above the lower cap. Send up the cross-trees by girt-lines, and let the after part rest on the lower cap and the forward part against the topmast. Lower away the topmast until the cross-trees fall into their place, and then hoist until they rest on the shoulders. Lash on the bolsters, get girt-lines on the cross-trees to send up the rigging, and then put it over the mast-head, first the shrouds, then the backstays, and lastly the head-stays. Sway the topmast on end, fid it, and set up the rigging.

TO GET ON A TOPMAST-CAP.--In vessels of the largest class, it may be necessary to send up the cap in the following manner, but it can usually be got up by hand. Or it may be fitted and the rigging put on over it. Send the cap up to the cross-trees by girt-lines, and place the round hole of the cap over the forward hole of the cross-trees; send aloft a topgallant studdingsail boom, and point its upper end through the holes in the cross-trees and cap, and lash the cap to it. Hook a tackle or girt-line to a strap on the lower end of the spar, and sway away until the cap is over the mast-head. Slue the spar so that the cap may come fair, lower away, and place the cap upon the mast-head. Unlash the spar and send it down.

TO RIG OUT A JIB-BOOM.--Point the outer end through the collars of the stays. Reeve the heel-rope through a block at the bowsprit cap, through the sheave-hole at the heel of the boom, and secure the end to an eye-bolt in the cap on the opposite side. Rig the boom out until the inner sheave-hole is clear of the cap. Tar the boom-end, put on the foot-ropes and guys, and reeve the jib stay. Hoist up the martingale and rig it, and reeve the martingale stay and gaub-line. Rig the boom out to its place, and set up the jib and martingale stays.

TO CROSS A LOWER YARD.--If the yard is alongside, reeve the yard rope through the jear block at the mast-head, make it fast to the slings of the yard, and stop it out to the yard-arm. Sway away, and cast off the stops as the yard comes over the side, and get the yard across the bulwarks. Lower yards are rigged now with iron trusses and quarter-blocks, which would be fitted before rigging the yard. Seize on the clew-garnet block, and put the rigging over the yard-arm; first the straps for the head-earings, then the foot-ropes, then the brace blocks or pennants, and last the eye of the lift. Reeve the lifts and braces, get two large tackles from the mast-head to the quarters of the yard, and sway away on them and on the lifts, bearing off and sluing the yard by means of guys. Secure the yard by the iron trusses, and haul taut lifts and braces.

TO CROSS A TOPSAIL YARD.--As topsail yards now have chain tyes, there are no tye-blocks to seize on. The quarter-blocks are first seized on, and the parral secured at one end, ready to be passed. A single parral has an eye in each end, and one end is passed under the yard and over, and the eye seized to the standing part, close to the yard. After the yard is crossed, the other end is passed round the mast, then round the yard, and seized in the same manner. To pass a double parral, proceed in the same manner, except that the seizings are passed so as to leave the eyes clear and above the standing part, and then take a short rope with an eye in each end, pass it round the mast, and seize the eyes to the eyes of the first long rope. The parral is wormed, served and leathered. The parral being seized at one end, put on the head-earing straps, the foot-ropes, Flemish horses, and brace blocks. Bend the yard-rope to the slings, stop it out to the yard-arm, and sway away until the yard is up and down; then put on the upper lift in the top and the lower lift on deck, and reeve the braces. Sway away, cast off the stops, and take in upon the lower lift as the yard rises, till the yard is square; then haul taut lifts and braces and pass the parral.

To send up a long topgallant mast, put the jack over the topmast cap, with a grommet upon its funnel for the eyes of the rigging to rest upon; send up the rigging by girtlines, and put the eyes over the jack, first the topgallant shrouds, backstays and stays, then the royal rigging in the same order, with a grommet, then the skysail stay and backstay, and lastly the truck. Reeve a top-rope forward through a block at the topmast-head, through the hole in the cross-trees; through the sheave-hole at the foot of the topgallant mast; carry it up the other side, and make it fast to its own part at the mast-head; stop it along the mast, and bend a guy to the heel. Sway away, and point through the jack; put on the truck, and the skysail, royal and topgallant rigging in their order; slue the mast so as to bring the sheaves of the tyes fore-and-aft; cast off the end of the top-rope, the mast hanging by the stops; make it fast to an eye-bolt on the starboard side of the cap, and sway away. When high enough, fid the mast and set up the rigging.

A short topgallant mast is sent up like a topmast, the cross-trees got over in the same manner; and the fidded royal-mast is sent up like a long topgallant mast.

TO RIG OUT A FLYING JIB-BOOM.--Ship the withe on the jib-boom end, reeve a heel-rope through a block at the jib-boom end, and bend it to the heel of the flying jib-boom, and stop it along, out to the end. Haul out on the heel-rope, point through the withe, put on the rigging, in the same order with that of the jib-boom; reeve the guys, martingale, flying jib, royal and skysail stays; rig out, and set up the rigging. The heel of the boom rests against the bowsprit cap, and is lashed to the jib-boom.

The flying jib-boom should be rigged fully out before the fore topgallant mast is swayed on end.

TO CROSS A TOPGALLANT YARD.--Seize on the parral and quarter-blocks; reeve the yard-rope through the sheave-hole of the topgallant mast, make it fast to the slings of the yard, and stop it out to the upper end. Sway away, and when the upper yard-arm has reached the topmast-head, put on the upper lift and brace; sway away again, put on the lower lift and brace, cast off all the stops, settle the yard down square by lifts and braces, and pass the parral lashing.

TO CROSS ROYAL YARDS.--The royal yards are crossed in the same manner as the topgallant yards, except that in most merchantmen they would be sent up by the halyards instead of a yard-rope. If there is not a standing skysail, the quarter-blocks on the royal yard will be single.

TO SEND DOWN MASTS AND YARDS.

To send down a royal yard--a topgallant yard--a topgallant mast. To house a topgallant mast. To send down a topmast. To rig in a jib boom.

TO SEND DOWN A ROYAL YARD.--If the sail is bent to the yard, furl it, making the gaskets fast to the tye. Cast off the sheets and clewlines, and make them fast to the jack. Be careful to unreeve the clewlines through the quarter-blocks. Cast off the parral-lashing. Overhaul the tye a little, and stop it to the yard, just outside of the quarter-block. If stopped too far out, the yard will not hoist high enough to get the lower lift off. Sway away on the halyards, which will cant the yard and hoist it. When high enough, cast off the lower lift and brace, and make them fast to the jack. Lower away, and as the upper yard-arm comes abreast of the jack, clap a stop round the yard and tye, near the yard-arm, and cast off the lift and brace, making them fast to the jack. Lower away to the deck.

If the halyards are not single, the yard must be sent down by a yard-rope, like the topgallant yard. In some vessels, instead of making the sheets and clewlines fast to the jack, overhand knots are taken in their ends, and they are let go. The sheets will run out to the topgallant yard-arms, and the clewlines will run to the fair-leaders in the cross-trees. In port, the main royal yard is sent down on the starboard side, and the fore and mizzen on the larboard; but at sea, the tye is stopped out on the lee side, and the yard sent down in any way that is the most convenient.

TO SEND DOWN A TOPGALLANT YARD.--Cast off the sheets, bowlines, buntlines and clewlines, and make them fast to the cross-trees. Reeve a yard-rope through a jack-block at the mast-head, unhook the tye, cast off the parral-lashing, bend the yard-rope to the slings of the yard by a fisherman's bend, and stop it to the quarters of the yard. Sway away, and take off the lifts and braces, as with the royal yard.

TO SEND DOWN A TOPGALLANT MAST.--Hook the top-block to the eye-bolt at the larboard side of the topmast cap; reeve the mast-rope through it, then through the sheave-hole in the foot of the topgallant mast, and hitch its end to the eye-bolt on the starboard side of the cap. Come up the rigging, stays and backstays, and guy the mast-head by them. Hoist a little on the mast-rope, and take out the fid. Lower away until the mast is a little short of being through the cap. Then seize or rack together both parts of the mast-rope just above the sheave-hole; cast off the end of the mast-rope, letting the mast hang by the stops, and hitch it round the mast-head to its own part, below the cap. Then lower away to the deck. If the rigging is to come on deck, round up the mast-rope for a girtline; if it is to remain aloft, lash it to the topmast cap, render the shrouds through the cross-trees, and stop them up and down the topgallant rigging. Sheep-shank the stays and backstays, and set them hand-taut. If the top-mast is also to be sent down, take off the topmast cap and send it on deck.

TO HOUSE A TOPGALLANT MAST.--Proceed in the same manner, except that when the mast is low enough, belay the mast-rope, pass a heel-lashing through the fid-hole and round the topmast.

TO SEND DOWN A TOPMAST.--Hook the top-block, reeve the mast-rope through it and through the sheave-hole in the foot of the mast, and hitch it to the staple at the other side of the cap. Lead the fall through a snatch-block, to the capstan. Sling the lower yard, if it is to remain aloft, and unshackle the trusses, if they are of iron. Come up the rigging, stays and backstays, weigh the mast, take out the fid, and lower away. If the rigging is to remain aloft, lash the cross-trees to the lower cap. The rigging should be stowed away snugly in the top, and the backstays be snaked up and down the lower rigging.

TO RIG IN A JIB-BOOM.--Reeve the heel-rope come up the stay, martingale stay and guys; unreeve the jib-stay, station hands at each guy, clear away the heel-lashing, haul in upon the guys, and light the boom on board. In most cases the boom will come in without a heel-rope. Make fast the eyes of the rigging to the bowsprit cap, and haul all taut.

Share on: WhatsApp @Hash Facebook Tweet